SMC Gateway er en liten, men kraftig linux basert datamaskin som kobler digitale radiosystemer til andre systemer.

Den fungerer som en bro mellom ulike enheter og kan automatisere oppgaver, noe som øker sikkerheten, kvalitetsikrer respons og sparer tid.

1. Brannalarm varsling på radio:

• SMC Gateway kan koble en rekke alarmer til radiosystemet:
  
  • Brannalarm
  • Innbruddsalarm
  • Nesten en hvilken som helst sensor alarm
• SMC sender da umiddelbar varsling til radiosystemet ved utløst alarm eller annen sensorovervåkning.
  
• Gatewayen kan samtidig automatisk sende ut SMS og e-post til predefinerte mottakere
  

2. Adgangskontroll med radio:

• Kan gi autoriserte personer tilgang til å åpne bommer, dører og porter fra radiosambandet
  
• Gatewayen logger all aktivitet og kan konfigureres til GPS sporing.
  

3. Telefontjenester integrert med radio:

• SMC Gateway kan settes opp til å fungerer som en telefonsentral som kobler samtaler til radiosambandet.
• Ring direkte til radioer eller talegrupper
• Radiobrukere kan ringe ut til eksterne predefinerte numre.

4. Detaljert forklaring på telefonintegrasjon:

• SMC Gateway kan kobler radiosystemet til analoge (PSTN) og IP-baserte (VOIP) telefonlinjer.
• Systemet kan settes opp med "virtuell telefonassistent" (IVR) som gir informasjon og veiler innringer videre.
• Gatewayen kan også fungere som en automatisk oppringingstjeneste (speech dialer) ved alarm.
• Talemeldinger kan tilpasses og sendes til ulike personer basert på situasjonen.

Eksempel på bruk:

En ansatt utløser en brannalarm på lageret. Gatewayen mottar umiddelbart alarmsignalet og sender en forhåndsdefinert melding til alle radioer i bygget. Samtidig ringer Gatewayen automatisk til brannvesenet og sender en SMS-varsling til sikkerhetsansvarlig.

5. Andre bruksområder for SMC Gateway:

• Sporing og overvåking: Få sanntidsposisjon på radioer, kjøretøy og personer med GPS.
• Flåtestyring: Optimaliser ruter og få oversikt over kjøretøyaktivitet på webbasert kart.
• Bygningsautomasjon: Integrer SMC Gateway med andre systemer for styring av lys, varme og ventilasjon.
• Sykehus og omsorgshjem: Koble pleiealarmer til radiosystemet for rask respons.

Fordeler med SMC Gateway:

• Økt sikkerhet gjennom rask varsling og koordinering.
• Bedre effektivitet med automatiserte oppgaver og sporing.
• Enklere kommunikasjon med integrering av telefon og radio.
• Stålkontroll med detaljert logging av all aktivitet.

ALARM VARSLING HYTERA

ALARM VARSLING TIL RADIOSAMBAND

KNYTTE TELEFONI TIL RADIOSAMBAND

ALARM VARSLING MED TEKSTMELDING TIL RADIO

EKSEMPEL OPPSETT PROSEDYRE FLYTSJEMA

KONFIGURERING TILGANGSKONTROLL FRA RADIO

• SMC-Gateway produsers i England og brukes over hele verden som smart, fleksibel, stabil og pålitelig løsning
• Kan sammenkoble og automtisere en rekke systemer og funksjoner for økt sikkerhet og effefkivitet
• For maksimal sikkert er SMC Gateway ikke knyttet til internet. 
• All programmering ligger i SMC Gateway boksen
• Brukergrensesnitt for Asterix for flowchart oppsett ol.
• Kobles til radiosystemer over repeater, men kan også kontakte radiosamband på andre måter.
• Kan konfigeres med telefonigateway til radiosamband

Fire and intruder alarm integration to radios, supporting all major BMS, intruder and fire alarm systems, as well as panic buttons, hard wired inputs, MOXA ioLogik devices and more. 

 

• Customise alarm messages to be radio friendly
• Filter based on location, zone or any other data
• Send messages to Radio, Email, SMS and more 
• Text to Speech for non keypad radios

 

Honeywell Notifier

Honeywell’s Notifier range of fire alarms are compatible with the SMC Gateway, with the full point location details being available including the breaking down of the message into it’s components:

• Alarm/Fault
• Panel (networked systems only)
• Zone
• Location
• Value
• Day
• Date
• Time
• Event ID

 

Both standalone and networked Notifier systems are supported, and connection to the Gateway is via either:

- Isolated RS232 option card (set to 80 column printer mode, and reset panel)

- On-board RS232 port (set to VDU/Dumb mode)

 

Kentec Syncro

The Kentec Syncro range of fire alarms are compatible with the SMC Gateway, with full point location details being available including the breaking down of the message into it’s components:

• Alarm/Fault
• Panel (networked systems only)
• Zone
• Location
• Address
• Loop
• Date
• Time

 

Connection from the Syncro fire alarm to the gateway is via the PC Data connection on the rear of the front panel. You will require the Kentec PC RS232/Data lead (X187LS) as the connector on the fire alarm is not a standard RS232 connector.

The serial connection defaults to 19200 8N1.

 

 

Kentec Taktis

The Kentec Syncro range of fire alarms are compatible with the SMC Gateway, with full point location details being available including the breaking down of the message into it’s components:

• Alarm/Fault
• Panel (networked systems only)
• Zone
• Location
• Address
• Loop
• Date
• Time

 

C-Tec XFP Series

The C-Tec XFP Series range of fire alarms are compatible with the SMC Gateway, with full point location details being available including the breaking down of the message into it’s components:

- Alarm/Fault

- Panel (networked systems only)

- Zone

- Location

- Address

- Loop

- Date

- Time

 

Connection from the C-Tec XFP fire alarm to the gateway is via the RS232 connection on the top left of the rear PCB. You will require a serial lead with bare ends as the fire alarm has screw terminal connections. We recommend the use of an RS232 optical isolator to avoid ground loop faults, and the CTS connection must be pulled high to a; enabled the data output and b; to prevent the printer fault/paper out error.

 

The SMC Gateway requires an OPT01 or OPT04 board to provide the RS232 connection. The serial connection defaults to 9600 8N1.

 

Important note

In our testing we found that events sent to the Gateway were not always being stored in the fire panels history, therefore we recommend using the Gateway to store the events instead of the panels history log.

Tyco/ADT MX2/MX4

TYCO/ADT’s range of MX2, MX4 and MZX fire alarms are compatible with the SMC Gateway, with the full point location details being available including the breaking down of the message into its components:

- Alarm/Fault

- Panel (networked systems only)

-Zone

- Location

- Date

- Time

- Device type

 

Both standalone and networked systems are supported, and connection to the gateway is via either:

- On-board COM1 port (set to default 9600, 8N1 printer mode)

- Optional MPM800 Multipurpose I/F module, configured as above (TYCO part #557.202.012)

 

The connection into the alarm panel is via a TYCO/ADT supplied lead which converts the panels RJ12 connector to either a 9 pin (TYCO part #125.021.905) or 25 pin serial connector (TYCO part #125.021.930). Importantly the DTR and CTS pins must be connected to each other to put the virtual printer online – without this connection, the panel will not send any data.

 

For reference, the RJ12 connections (and TYCO lead colours) are:

 

1 – Blue – Ground

2 – Yellow – RX

3 – Green – TX

4 – Red – CTS

5 – Black – DTR

6 – White – DSR

 

So, to connect to the SMC Gateway, short out the Red (CTS) & Black (DTR) cores, and connect the Blue (Gnd) to Gnd, and the Green (TX) to the Serial RX on the SMC Gateway.

Ziton

The Ziton range of fire alarms are compatible with the SMC Gateway, with full point location details being available including the breaking down of the message into it’s components:

- Alarm/Fault

- Panel (networked systems only)

- Zone

- Location

- Date

- Time 

- Event ID

 

Connection from the Ziton fire alarm to the gateway is via the optional RS232 board.

 

The SMC Gateway requires an OPT01 or OPT04 board to provide the RS232 connection.

Gent Vigilon

Gent’s Vigilon range of fire alarms are compatible with the SMC Gateway, with the full point location details being available including the breaking down of the message into it’s components:

- Alarm/Fault

- Zone/Sector

- Location

- Date 

- Time

 

Connection to the gateway is via Gent’s optional RS232 printer card, which defaults to 9600,8,n,1, and connection is via directly wired terminals

 

 

Advanced MX

The Advanced MX Pro range of fire alarm panels are compatible with the SMC Gateway, with full point location detail being available including a full breakdown of the message into:

- Device

- Zone

- Location

- Event type

- Time

- Date

 

Connection to the fire alarm panel is via a serial connection

 

 

 

 

SIP/PSTN telephone to radio system interconnect, with advanced call bridging, speech dialler and call routing.

 

• All major radio systems supported
• Customisable IVR menus
• Fallback in case of no-reply
• Various connection methods

 

 

 

 

 

Multiple speech dialler modules are supported, each can have their own audio file and have differing actions and escalation assigned. 

 

• Multiple speech diallers
• Choose who to call
• Acknowledgments
• Escalation
• Various connection methods
• Simple webapp to manage and monitor

 

 

 

 

Intelligent Access Control

 

• Control gates, barriers and more
• Log usage
• Monitoring
• Reporting
• Raise alarms
• SIP intercom support

 

 

 

 

 

Find your assets. Respond to emergencies. Plan your event. 

Browser based, multi-user application, supporting radio and cellular devices.

 

• Complete solution, hardware included
•  Web appplication, no software to install
•  Real Time GPS tracking of radios and mobile devices
•  Custom mapping
•  Off-line mapping
•  Open street map, Google maps and Google Satellite
•  Emergency notifications
•  Reverse Geocoding for fast address lookup

 

 

Connects mobile workers to administrators, other departments, and users outside of the radio network. 

 

• Two-way radio to and from email 
• Two-way radio to and from SMS
• Integrates third-party systems to the radio network

 

 

 

Every Radio Call, Logged and Stored

 

When you need a full audit trail, Record makes sure you know you who said what and when.

 

• Web application, no software to install
• 2 Radio channels supported
• Local, USB or remote storage
• Download and playback recordings
• Definable retention policy 
• GDPR compliant
•  All major radio systems supported

 

 

 

 

Locate your people and assets when GPS is not available or other technologies are unreliable.

 

Indoor Positioning, or Internal Tracking as its sometimes known, uses low-cost Bluetooth beacons to detect nearby devices, these devices can then be overlaid on plans and displayed. 

 

The application allows the upload of your plans and drawings, placement of beacons and the ability to create views, which can contain multiple plans to provide a completely custom user experience. 

 

Designed to run on the Gateway V2, the application can harness the powerful business logic already built in to raise alarms and messages based on the location of devices and their state. For example, the location of a radio could be used to automatically trigger lone work routines when entering hazardous areas, or alert others via radio, SMS or telephone of an emergency.

 

 

 

 

This neat solution works with Hytera’s work order feature to manage the allocation of work orders also known as job tickets. 

• Networked, browser application
• Unlimited operators
• Simple to use for operators and radio users 
• Reporting engine with export facilities 
• Ad hoc text messaging